Featured

How to Cut Miter Joints at the Router Table

Chamfer Router Bits

Our chamfer router bits will make any chamfer or bevel task a lot easier. Simply adjusting the height of the router bit will produce an almost endless variety of attractive, functional chamfers. This edge is perfect for beams, columns or other large timers. Use your Chamfer router bits to produce multi-sided boxes, planters, waste-baskets or decorative pieces.

When it comes time to make 45° miters, most of us go straight to the table saw. Depending on the workpiece and how accurately the stops in your saw are set, the table saw can make getting good results a challenge. The router table, on the other hand, can be a perfect solution. All you need is an Infinity Cutting Tools 36-950 Chamfer bit. I know what you're thinking: When I see a chamfer bit, I don't think of making miters joints. But the 36-950 is not your ordinary chamfer bit. In fact, the 36-950 chamfer bit is capable of mitering material up to 1-1/8" thick without batting an eye. Don't be concerned by the size of this bit — it's a mild-mannered beast that makes a great addition to any shop with a variable speed router. Let me share a couple of tips that will make the router table your go-to tool for miters.

The 36-950 45° Chamfer bit is for use in the router table and can be run at around 18,000 RPM for smooth miters in material up to 1-1/8
The 36-950 45° Chamfer bit is for use in the router table and can be run at around 18,000 RPM for smooth miters in material up to 1-1/8" thick.

Cutting straight, long miters (with the grain) are the hardest at the table saw, at least for me. Depending on the tilt of the blade and the position of the fence this job always seems a little scary. No matter how everything is positioned one of the pieces always seems poised to launch back at the end of the cut. This is not an issue at the router table because there is no off-cut piece. The fence on the router table can be positioned right where you need it, making it much easier to get precise results. With a couple of good feather boards or a set of Jessem Clear-Cut Router Stock Guides, the piece is held securely reducing vibration and making it easy to guide the workpiece through the cut.

To provide support to the razor-sharp edge after the cut I like to use a piece of scrap and a couple pieces of double-sided tape to create a support to ride against the router table fence.
To provide support to the razor-sharp edge after the cut I like to use a piece of scrap and a couple pieces of double-sided tape to create a support to ride against the router table fence.

One tip for making razor-sharp miters at the router table is to use a straight piece of material stuck to the top of your workpiece with double sided tape as a fence. This piece protects the delicate edge of the miter after the cut and acts as a bearing surface to ensure a snipe-free cut. This trick works equally well when routing both with and across the grain.

The support ensures the delicate tip of the miter is not damaged or crushed on the outfeed side of the cut.
The support ensures the delicate tip of the miter is not damaged or crushed on the outfeed side of the cut.

The Vertical Router Sled is a perfect choice when it comes to mitering narrow stock. It holds the workpiece vertically and ensures accurate wobble-free cuts. It also speeds up the process when mitering both ends of a piece for making projects like boxes or trays. With all 4 pieces cut to the proper length it is simply a matter of setting up the sled and then it's off to the races with a cut/flip/cut operation.

The Vertical Router Sled makes it easy to miter narrow stock and insures a square wobble- free cut.
The Vertical Router Sled makes it easy to miter narrow stock and insures a square wobble- free cut.

Setting up the chamfer bit is easy. Simply align the faces of the fence with the bearing using a ruler, leaving only the height setting to worry about. Mitering at the router table means the workpiece can be cut to its final outside dimension and then mitered.  For me, trying to measure and ensure the correct cut on a tilted table saw blade is much more difficult to get just right.

The bearing on the top of the bit make the fence setting a breeze leaving only the bit height to be adjusted to the thickness of the work piece.
The bearing on the top of the bit make the fence setting a breeze leaving only the bit height to be adjusted to the thickness of the work piece.

Next time you have a project that requires a miter joint, give the router table method a try. I think it will become your preferred method.